Hardware Builder'S Hardware
- Builder'S Hardware Braces Plates & Corner Irons
- Builder'S Hardware Bracing & Spacers
- Builder'S Hardware Deck Hardware
- Builder'S Hardware Foundation & Post Hardware
- Builder'S Hardware Framing Connectors
- Builder'S Hardware Hurricane Ties & Clips
- Builder'S Hardware Plates
- Builder'S Hardware Straps & Strapping
-
$2.25DTT (deck tension ties) are safe, cost-effective connectors designed to meet or exceed code requirements for deck construction. These versatile DTT connectors are also load rated as a holdown for light-duty shearwalls and braced wall panel applications. The DTT1Z deck tension tie provides a less invasive approach for attaching a…
-
$0.50Nail stoppers help prevent nails from piercing water pipes and electrical lines. Installed over utilities that pass through framing members. 16-gauge galvanized steel.
-
$0.80For alignment control between a roof truss and non-bearing walls; the 1-1/2″ slot permits vertical truss chord movement when loads are applied. 1-1/4″ W. x 2-3/4″ H. x 1-7/8″ D.
-
$0.65Provide a tension connection between 2 wood members. They resist uplift at the heel of a truss economically. The 2 In. bend section eliminates interference at the transition points between wood members.
-
$0.90Provide a tension connection between 2 wood members. They resist uplift at the heel of a truss economically. The 2 In. bend section eliminates interference at the transition points between wood members.
-
$0.65Designed for use on the edge of 2x members, with a nailing pattern that reduces the potential for splitting. They can be used where plates or soles are cut, at wall intersections, and as ridge ties. Galvanized steel. Also available with ZMAX coating.
-
$1.15Designed for use on the edge of 2x members, with a nailing pattern that reduces the potential for splitting. They can be used where plates or soles are cut, at wall intersections, and as ridge ties. Galvanized steel. Also available with ZMAX coating.
-
$1.00Designed for use on the edge of 2x members, with a nailing pattern that reduces the potential for splitting. They can be used where plates or soles are cut, at wall intersections, and as ridge ties. Galvanized steel.
-
$19.00Continuous utility straps can be cut to length on the job site. These connectors are designed to help resist tension forces. Galvanized steel.
-
$9.25Continuous utility straps can be cut to length on the job site. These connectors are designed to help resist tension forces. Galvanized steel.
-
$30.68Continuous utility straps can be cut to length on the job site. These connectors are designed to help resist tension forces. Galvanized steel.
-
$2.95Designed to transfer tension loads in a wide variety of applications. The HRS has a nailing pattern designed for installation on the edge of 2x members. 12-gauge galvanized steel. The model No. HRS416Z is ZMAX coated and is installed with Simpson Strong-Tie Strong Drive screws (SDS).
-
$1.15Designed to transfer tension loads in a wide variety of applications. The HRS has a nailing pattern designed for installation on the edge of 2x members. 12-gauge galvanized steel. The model No. HRS416Z is ZMAX coated and is installed with Simpson Strong-Tie Strong Drive screws (SDS).
-
$1.15Designed to transfer tension loads in a wide variety of applications. The HRS has a nailing pattern designed for installation on the edge of 2x members. 12-gauge galvanized steel. The model No. HRS416Z is ZMAX coated and is installed with Simpson Strong-Tie Strong Drive screws (SDS).
-
$1.75Designed for 4×2 floor trusses and 4x beams. For the THA29, nails used for joist attachment must be driven at an angle so that they penetrate through the corner of the joist and into the header. For face mount installation, install all face nails according to the table. Minimum carried…
-
$1.30Bearing plates give greater bearing surface than standard cut washers and help distribute the load at these critical connections.