Builder'S Hardware Foundation & Post Hardware
-
$1.90The BC series offers dual purpose post cap/base for light cap or base connections. Do not install bolts into pilot holes. Install with 16d common nails or 16d x 2-1/2″ joist hanger nails. Post bases do not provide adequate resistance to prevent members from rotating about the base and are…
-
$1.90These connectors are always installed in pairs and connect 4x or 6x wood members at right angles. Eliminates driving nails into end grain. Nails can be added in the triangle holes to increase uplift load capacity. 18-gauge galvanized steel. Some sizes available with ZMAX coating.
-
$1.25The BC series offers dual-purpose post cap/base for light cap or base connections. Do not install bolts into pilot holes. Install with 16d common nails or 16d x 2-1/2″ joist hanger nails. Post bases do not provide adequate resistance to prevent members from rotating about the base and are not…
-
$3.90These connectors are always installed in pairs and connect 4x or 6x wood members at right angles. Eliminates driving nails into end grain. Nails can be added in the triangle holes to increase uplift load capacity. ZMAX galvanized steel.
-
$2.90These connectors are always installed in pairs and connect 4x or 6x wood members at right angles. Eliminates driving nails into end grain. Nails can be added in the triangle holes to increase uplift load capacity. 18-gauge galvanized steel. Some sizes available with ZMAX coating.
-
$3.00The LCE4’s universal design provides high-capacity while eliminating the need for rights and lefts. For use with 4x or 6x lumber. Install in pairs. Dimension: 5-3/8″ long. Use 14-16d galvanized fasteners in beam and 10-16d galvanized fasteners in post. 20-gauge ZMAX galvanized steel.
-
$8.40Simpson Strong-Tie column bases, install all models with bottom of base plate flush with the concrete. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or unbraced carports). Strap is 7-gauge x…
-
$42.40Column caps provide a strong connection for column-beam combinations. This design uses Strong-Drive SDS Heavy-Duty Connector screws to provide faster installation and provides a greater net section area of the column compared to bolts. The SDS screws provide for a lower profile compared to standard through bolts.
-
$11.75Simpson Strong-Tie column bases, install all models with bottom of base plate flush with the concrete. Post bases do not provide adequate resistance to prevent members from rotating about the base and therefore are not recommended for non top-supported installations (such as fences or unbraced carports). Strap is 7-gauge x…
-
$6.40Embed into wet concrete up to the bottom of the 1″ standoff base plate. A 2″ minimum side cover is required to obtain the full load. Holes in the bottom of the straps allow for free concrete flow. Post bases do not provide adequate resistance to prevent members from rotating…
-
$11.00The CBSQ uses Simpson Strong-Tie Strong-Drive screws (SDS), which allow for fast installation, reduced reveal and high capacity, provides a greater net section area of the column compared to bolts. Install Simpson Strong-Tie SDS 1/4″ x 2″ wood screws, which are provided with the column base. (Lag screws do not…
-
$26.50The ABU is an adjustable post base which offers moisture protection and finished hardware appearance. Manufactured with ZMAX steel for enhanced corrosion resistance. These post bases feature a 1″ stand-off height above concrete floors, code-required when supporting permanent structures that are exposed to the weather, or water splash, or in…
-
$8.90The ABA is an adjustable post base which offers moisture protection and finished hardware appearance. These post bases feature a 1″ standoff height above concrete floors, code-required when supporting permanent structures that are exposed to the weather, or water splash, or in basements. They reduce the potential for decay at…
-
$9.50The PC cap provides a custom connection for post-beam combinations at medium design loads. Miminum 4×4 post size. Do not install bolts into pilot holes. 16-gauge galvanized steel. Also available with ZMAX coating.
-
$10.75An adjustable retrofit post base with a 1″ standoff and increased capacity to resist uplift loads. Features a slot in the ABW that allows flexible positioning around the anchor bolt making precise post placement easier. The 1″ standoff helps prevent rot at the end of the post and meets code…
-
$5.00The BC series offers dual purpose post cap/base for light cap or base connections. Do not install bolts into pilot holes. Install with 16d common nails or 16d x 2-1/2″ joist hanger nails. Post bases do not provide adequate resistance to prevent members from rotating about the base and are…